Ambient IoT Backscatter Devices as Passive Anchors for NLOS Cellular Positioning: Fundamental Limits

Ambient Internet-of-Things backscatter devices at known locations can act as low-cost passive anchors by creating geometrically anchored reflected paths in cellular networks. Unlike reconfigurable intelligent surfaces, practical backscatter devices are independently controlled and lack a common phase reference; their modulation signatures may be known, but their reflection gains and residual phases are generally uncalibrated. We study how much localization information survives this incomplete per-device calibration in uplink non-line-of-sight (NLOS) positioning, where the direct NLOS path and the backscatter-assisted paths share an unknown scatterer. Treating the common channel gain, the relative backscatter response, and the residual device phases as nuisance parameters, we derive closed-form equivalent Fisher information matrices for calibrated, partially calibrated, and fully uncalibrated operation. The analysis shows that unknown device phases remove carrier-phase information from the backscatter-assisted paths, whereas joint uncertainty in the common gain and relative response leaves the direct NLOS path with only bandwidth-dependent delay information. The resulting position-domain bounds show that device count alone is insufficient: the passive anchors must also observe the common scatterer from sufficiently diverse directions. For joint single-snapshot identification of the user equipment and scatterer, at least two devices in two dimensions and three in three dimensions are necessary. The results identify deployment implications for Ambient Internet-of-Things positioning and show which calibration losses also apply to separable subpanel-based reconfigurable-surface architectures.

Backscatter Assisted Indoor NLOS Positioning

Passive backscatter devices (BDs) can enable indoor non-line-of-sight (NLOS) positioning by serving as virtual anchors whose Doppler-separated signatures are observable in standard channel estimates. This paper studies continuous user-equipment (UE) tracking in corridor environments using a noncoherent power-domain formulation that avoids BD phase synchronization and remains robust to residual carrier offsets and strong multipath. The BD-dependent measurements are modeled by a log-distance law with unknown BD-specific offsets, which allows passive asynchronous devices to be used as anchors without transmit-power calibration. Based on this model, we develop a corridor-constrained maximum a posteriori (MAP) tracker with motion regularization and Huber-robust estimation. In ray-tracing-inspired simulations, the method achieves median positioning errors of 0.23--0.27 m with 90th-percentile errors below 0.45 m. In office-corridor measurements with four passive BDs at 866 MHz, it attains an aggregated median error of 0.505 m and outperforms a simple weighted-average baseline. The results show that passive asynchronous BDs can provide practical sub-meter indoor NLOS tracking while remaining compatible with existing channel-estimation pipelines and energy-autonomous BD deployments.

Self-Calibrated Indoor Tracking from Backscatter Fiducials under NLOS Transmitter Illumination

This paper studies indoor tracking from wall-mounted backscatter fiducials in corridor segments outside direct transmitter illumination. In the measured setup, the transmitter-to-fiducial links are NLOS, whereas the fiducial-to-receiver links along the corridor are largely LOS. The main challenge is that the effective fiducial response is deployment-dependent, so a fixed calibrated link budget is not reliable. We therefore use a grid-based penalized-likelihood tracker that profiles the receiver path, a fitted log-distance slope parameter, and fiducial-specific offsets directly from received powers. The resulting paths can then be reused as surrogate calibration coordinates for residual-map correction, while the same correction with measured calibration coordinates is reported only as a reference. On a short four-fiducial corridor segment, the profiled dual-band tracker gives a 0.52 m median error without measured calibration coordinates, and surrogate residual correction improves this to 0.46 m. With measured calibration coordinates, the same correction and a RADAR-style fingerprint reference both reach 0.31 m. The main remaining limitation is therefore the quality of the surrogate calibration paths rather than the structured observation model itself.

Non-Invasive Arterial Pulse Detection with Millimeter-wave Radar and Comparison With Photoplethysmography

Cardiovascular diseases remain a leading cause of mortality and disability. The convenient measurement of cardiovascular health using smart systems is therefore a key enabler to foster accurate and early detection and diagnosis of cardiovascular diseases and it require accessing a correct pulse morphology similar to arterial pressure wave. This paper investigates the comparison between different sensor modalities, such as mmWave and photoplethysmography from the same physiological site and reference continuous non-invasive blood pressure devide. We have developed a hardware prototype and established an experiment consist of 23 test participants. Both mmWave and PPG are capable of detecting inter-beat intervals. mmWave is providing more accurate arterial pulse waveform than green photoplethysmography.