Admittance Controller Complemented with Real-time Singularity Avoidance for Rehabilitation Parallel Robots

Rehabilitation tasks demand robust and accurate trajectory-tracking performance, mainly achieved with parallel robots. In this field, limiting the value of the force exerted on the patient is crucial, especially when an injured limb is involved. In human-robot interaction studies, the admittance controller modifies the location of the robot according to the user efforts driving the end-effector to an arbitrary location within the workspace. However, a parallel robot has singularities within the workspace, making implementing a conventional admittance controller unsafe. Thus, this study proposes an admittance controller that overcomes the limitations of singular configurations by using a real-time singularity avoidance algorithm. The singularity avoidance algorithm modifies the original trajectory based on the actual location of the parallel robot. The complemented admittance controller is applied to a 4 degrees of freedom parallel robot for knee rehabilitation. In this case, the actual location is measured by a 3D tracking system because the location calculated by the forward kinematics is inaccurate in the vicinity of a singularity. The experimental results verify the effectiveness of the proposed admittance controller for safe knee rehabilitation exercises

Experimental Analysis of Type II Singularities and Assembly Change Points in a 3UPS+RPU Parallel Robot

Parallel robots (PRs) have singular configurations where the robot gains at least one degree of freedom and loses control. Theoretically, such singularity occurs when the Forward Jacobian-matrix determinant becomes zero (Type II). However, actual PRs could lose control owing to Type II singularities for determinant values near zero, but not zero, because manufacturing tolerances introduce errors that are complex to model due to their low repeatability. Thus, using an actual 3UPS+RPU PR, this paper presents three contributions: i) a proximity detection index for Type II singularities based on the angle between two Output Twist Screws. The index can identify which kinematic chains contribute to the singularity. ii) an experimental benchmark to study Type II singularities. iii) PR configurations where the proposed index is zero and the Forward Jacobian determinant is not. In this last configuration, the findings show that the actual robot is unable to handle external actions applied to the PR.

Mechatronic Design, Experimental Setup and Control Architecture Design of a Novel 4 DoF Parallel Manipulator

Although parallel manipulators (PMs) started with the introduction of architectures with 6 Degrees of Freedom (DoF), a vast number of applications require less than 6 DoF. Consequently, scholars have proposed architectures with 3 DoF and 4 DoF, but relatively few 4 DoF PMs have become prototypes, especially of the two rotation (2R) and two translation (2T) motion types. In this paper, we explain the mechatronics design, prototype and control architecture design of a 4 DoF PM with 2R2T motions. We chose to design a 4 DoF manipulator based on the motion needed to complete the tasks of lower limb rehabilitation. To the author's best knowledge, PMs between 3 and 6 DoF for rehabilitation of lower limbs have not been proposed to date. The developed architecture enhances the three minimum DoF required by adding a 4 DoF which allows combinations of normal or tangential efforts in the joints, or torque acting on the knee. We put forward the inverse and forward displacement equations, describe the prototype, perform the experimental setup, and develop the hardware and control architecture. The tracking accuracy experiments from the proposed controller show that the manipulator can accomplish the required application.

Reconfiguration of a parallel kinematic manipulator with 2T2R motions for avoiding singularities through minimizing actuator forces

This paper aims to develop an approach for the reconfiguration of a parallel kinematic manipulator (PKM) with four degrees of freedom (DoF) designed to tackle tasks of diagnosis and rehabilitation in an injured knee. The original layout of the 4-DoF manipulator presents Type-II singular configurations within its workspace. Thus, we proposed to reconfigure the manipulator to avoid such singularities (owing to the Forward Jacobian of the PKM) during typical rehabilitation trajectories. We achieve the reconfiguration of the PKM through a minimization problem where the design variables correspond to the anchoring points of the robot limbs on fixed and mobile platforms. The objective function relies on the minimization of the forces exerted by the actuators for a specific trajectory. The minimization problem considers constraint equations to avoid Type-II singularities, which guarantee the feasibility of the active generalized coordinates for a particular path. To evaluate the proposed conceptual strategy, we build a prototype where reconfiguration occurs by moving the position of the anchoring points to holes bored in the fixed and mobile platforms. Simulations and experiments of several study cases enable testing the strategy performance. The results show that the reconfiguration strategy allows obtaining trajectories having minimum actuation forces without Type-II singularities.